spec no: dsag4999 rev no: v.10a date: jan/09/2015 page: 1 of 5 approved: wynec checked: joe lee drawn: p.cheng er p: 1361000056 surface mount display part number: acpsc04-41surkwa hyper red features ? 0.4 inch character height. ? low current operation. ? high contrast and light output. ? categorized for luminous intensity. ? mechanically rugged. ? gray face,white segment. ? package : 400pcs / reel. ? moisture sensitivity level : level 2a. ? rohs compliant. description the hyper red source color devices are made with al- gainp on gaas substrat e light emitting diode. package dimensions& internal circuit diagram notes: 1. all dimensions are in millimeters (inches), tolerance is 0.25(0.01")unless otherwise noted. 2. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 3.the gap between the reflector and pcb shall not exceed 0.25mm
spec no: dsag4999 rev no: v.10a date: jan/09/2015 page: 2 of 5 approved: wynec checked: joe lee drawn: p.cheng er p: 1361000056 selection guide absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c note: 1. 1/10 duty cycle, 0.1ms pulse width. parameter hyper red units power dissipation 75 mw dc forward current 30 ma peak forward current [1] 185 ma reverse voltage 5 v operating / storage temperature -40c to +85c note: 1. luminous intensity/ luminous flux: +/-15%. *luminous intensity value is traceable to the cie127-2007 compliant national standards. part no. dice lens type iv (ucd) [1] @ 10ma description min. typ. hyper red (algainp) white diffused 14000 36000 common cathode, rt. hand decimal. * 3600 * 8300 acpsc04-41surkwa symbol parameter device typ. max. units test conditions peak peak wavelength hyper red 645 nm i f =20ma d [1] dominant wavelength hyper red 630 nm i f =20ma ? 1/2 spectral line half-width hyper red 28 nm i f =20ma c capacitance hyper red 35 pf v f =0v;f=1mhz v f [2] forward voltage hyper red 1.95 2.5 v i f =20ma i r reverse current hyper red 10 ua v r =5v notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4. excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradatio n or premature failure.
spec no: dsag4999 rev no: v.10a date: jan/09/2015 page: 3 of 5 approved: wynec checked: joe lee drawn: p.cheng er p: 1361000056 hyper red acpsc04-41surkwa
spec no: dsag4999 rev no: v.10a date: jan/09/2015 page: 4 of 5 approved: wynec checked: joe lee drawn: p.cheng er p: 1361000056 acpsc04-41surkwa recommended soldering pattern (units : mm; tolerance: 0.15) reel dimension tape specifications (units : mm)
spec no: dsag4999 rev no: v.10a date: jan/09/2015 page: 5 of 5 approved: wynec checked: joe lee drawn: p.cheng er p: 1361000056 packing & label specifications acpsc04-41surkwa terms and conditions for the usage of this document 1.the information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before product ion usage customer should refer to the latest datasheet for the updated specifications. 3.when using the products referenced in this docu ment, please make sure the product is being operated within the environmental and electrical limit s specified in the datasheet. if customer usage exceeds the specified limits, kingbright w ill not be responsible for any subsequent issues. 4.the information in this document applies to typical usage in consumer electronics applications. if customer's application has special reliabilit y requirements or have life-threatening liabilities, such as automotive or medical usage, please co nsult with kingbright representative for further assistance. 5.the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6.all design applications should refer to ki ngbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
